FASTECH

Ezi-IO-EN-AD08-T

Settings and Operation

Switch

1. Ethernet IP Setting Switch (SW1, SW2): These switches set the 4th octet of Ethernet IP.  The 1st octet, the 2nd octet, and the 3rd octet are set by GUI. If the switches are set to 255(FF), DHCP function is activated, and IP is automatically set, ignoring the set value.
(Please refer to the manual for details.)

e.g.,) In case of SW2 : 5 and SW1 : 7
        (5×16) + (7×1) = 87
        IP is to be set as 192.168.0.87

2. Input Mode (Voltage/Current) Selection Switch (SW4)

SW4 is a switch that selects voltage/current mode for each channel.
Refer to the following chart for how to use SW4.

Switch Mode	CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8
Switch Mode	SW4.1	SW4.2	SW4.3	SW4.4	SW4.5	SW4.6	SW4.7	SW4.8
Voltage Input	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF
Current Input	ON	ON	ON	ON	ON	ON	ON	ON

＊Select the input mode for each channel with the Input Mode Selection Switch (SW4) before supplying power to the module.

3. Voltage Input Range Setting Switch (SW3)

SW3 is a switch for setting the input range.
You can set the range with the combination of the switches.

• Selecting Input Setting Method
You can select the input seting method with the LSET (SW3.1) switch as follows.

Switch Mode	LSET SW3.1	Description
Switch Mode	DIP Switch	ON	Setting voltage input range with DIP switches (SW3.3~SW3.10)
Ethernet communication	OFF	Setting input range with Ethernet communication.

* If you use any channels in current input mode, the setting method has to be Ethernet Communication (SW3.1=OFF).
* Set SW3.1 according to the desired method before supplying power to the module.
* SW3.2 is not used.

• Voltage Input Setting
When using the DIP Switch for setting (SW3.1 = ON), the voltage input is set as shown in the table below.

Switch Input Range	CH1/CH2		CH3/CH4		CH5/CH6		CH7/CH8
Switch Input Range	SW3.3	SW3.4	SW3.5	SW3.6	SW3.7	SW3.8	SW3.9	SW3.10
-10~10V	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF
-5~5V	OFF	ON	OFF	ON	OFF	ON	OFF	ON
-2.5~2.5V	ON	OFF	ON	OFF	ON	OFF	ON	OFF
0~10V	ON	ON	ON	ON	ON	ON	ON	ON

Status LED

1. Power Status LED

Name	Color	Status	Description
PWR	Red	OFF	Power is OFF
PWR	Red	ON	Power is ON

2. Operation Status LED

Name	Color	Status	Description
RUN	Green	OFF	Abnormal Operation
RUN	Green	Blinkig	Normal Operation

3. Ethernet Status LED

Name	Color	Status	Description
LINK1, LINK2	Green	OFF	Link not Established
LINK1, LINK2	Green	ON	Link Established

4. Ethernet Status LED

Name	Color	Status	Description
ACT1, ACT2	Yellow	OFF	Stand-by
ACT1, ACT2	Yellow	Flickering	In Operation

Connector

1. Power Connector(CN1)

No.	Fuction	I/O
1	DC24V	Input
2	GND	Input

2. Inpit Signal Connector(CN2)

No.	Name	Fuction	I/O
1	G	Analog GND	Input
2	G	Analog GND	Input
3	1	Analog In 1	Input
4	2	Analog In 2	Input
5	3	Analog In 3	Input
6	4	Analog In 4	Input

No.	Name	Fuction	I/O
7	5	Analog In 5	Input
8	6	Analog In 6	Input
9	7	Analog In 7	Input
10	8	Analog In 8	Input
11	G	Analog GND	Input
12	G	Analog GND	Input

3. Ethernet Communication Connector(CN3, CN4)

No.	Fuction
1	TD+
2	TD-
3	RD+
4	----
5	----
6	RD-
7	----
8	----
Connector Hood	F.GND

Accessories - Connectors

Purpose	Item	Part Number	Manufacturer
Power(CN1)	Terminal Block	MC421-38102	DECA

※ The connectors above are supplied with the product. If you are using other parts, please make sure they meet the specifications.

Options - Ethernet Cable

Purpose	Part Number	Length [m]	Remarks
Ethernet Connection (CN3, CN4)	CGNR-EC-001F CGNR-EC-002F CGNR-EC-003F CGNR-EC-005F	1 2 3 5	· STP (Shielded Twisted Pair) Cable · Category 5e or higher · Maximum Length: 100m · Normal Cable

※ If you need cables with length(in units of 1m) not listed on the table or robot cables, please contact FASTECH for more information.